OscarWatch CW

Tools → OscarWatch CW reads Morse from the radio and writes it down. This window is receive only: it never transmits. To send CW, use the CW keyer in the logbook.

Decoding uses the DeepCW model by e04, under the MIT licence. It runs on your computer. No audio leaves the machine.

Getting started

  1. Connect your receiver audio to the PC (soundcard line in, or the radio's USB audio).
  2. Open Tools → OscarWatch CW. Only one window can be open. Choosing the menu again brings that window forward.
  3. Press Settings and choose the Input device. The same dialogue holds the Doppler, noise, text size and automatic start options.
  4. Put the frequency panel on CW for the satellite you are working, then press Start. The status line says Listening, and the name of the satellite in focus.

The Level bar shows whether audio is arriving. Set the level so it moves during Morse and does not sit hard against the top.

The waterfall

The waterfall shows receive audio from 0 to 2000 Hz. The decoder reads the shaded band. That band starts at 400 to 1200 Hz.

  • Click a CW trace to decode that signal.
  • Right-click to put the band back to 400 to 1200 Hz.
  • The yellow line marks the strongest steady note. If the status says the note is outside the decode band, click that trace.

Follow the note as it drifts is on by default. It keeps the steady note nearest the middle of the shaded band in the middle, so Doppler drift does not carry it out of the band. Click a trace to decode another signal. Right-click puts the band back.

The copy

The text appears about 2 seconds behind the signal. Each line starts with a UTC time. The newest letters may still change while the character is finishing.

Underlined callsigns and locators go into the logbook entry when you click them, or when you press Enter or Space. Your own callsign and your own locator are left as ordinary text. Nothing is logged until you press Add in the logbook. If the logbook is already editing a saved contact, save or cancel that edit first.

Calls and locators are shaded against every logbook, in the same colours as FT4. A key above the copy shows them:

  • Blue: a new call, not in any of your logbooks.
  • Purple: a new grid, a 4-character field you have no QSO in yet.
  • Grey: worked before.
  • Amber: your own callsign, so you can spot someone calling you.

The shading updates as soon as you add a QSO, including words already on screen. A call with a portable suffix such as /P counts as worked if you have the home call.

The status strip shows the sending speed in words per minute while a signal is keyed. It is most accurate up to about 30 wpm.

Clear wipes the copy and starts decoding afresh. Save copy writes the text to a file, with the UTC times.

Hide stray letters from noise is on by default. It drops words of one or two letters when the model is unsure. Those are almost always noise between overs. A short word the model is sure about, such as K, stays.

Doppler on SSB

On FM, a small tuning error does not move the audio note. On SSB, rig control tunes in steps and the CW note drifts between those steps.

Correct the note for rig control Doppler steps is on by default. OscarWatch shifts the audio back by that difference before decoding, so the note stays where you tuned it. The waterfall is drawn from the corrected audio too, so a trace stays steady instead of zig-zagging with each rig step. The radio is not retuned.

Some wobble can remain. It comes from the other station's uplink Doppler correction, their transmitter drifting as it warms up, or the satellite's transponder. Follow the note as it drifts keeps the decode band on it.

Automatic start

In Settings, tick Start listening when the focused satellite rises. The CW window must stay open, and the frequency panel must be on CW. Listening starts when the satellite climbs through the start elevation, and stops when it sets. The default is -5°, and you can set it from -15° to 30°. It is off until you tick it.

Text size

Decoded text size in Settings runs from 10 to 40. The default is 16. In the CW window, hold Ctrl and turn the mouse wheel over the copy, or press Ctrl with plus or minus. Ctrl+0 returns to 16.

Sending

This window does not transmit. To send CQ, a callsign or a report from the logbook, use the CW keyer.

Problems?

  • Nothing decodes: check the Level bar moves during Morse, and that the right input is selected. If the note sits outside the shaded band, click it.
  • "No audio is reaching OscarWatch": the selected input is silent. System default is often a microphone. Choose the radio's audio interface in Settings.
  • The copy is a couple of seconds late: the decoder waits until it is sure of the letters. That delay is normal.
  • Stray letters between overs: leave Hide stray letters from noise ticked.
OscarWatch
OscarWatch
Toggle sidebar