ICOM IC-9700 with OscarWatch Tracker

This guide is for operators who use an IC-9700 as the only radio on a pass. If you pair the 9700 with a second rig, read ICOM dual radio as well. For other ICOM satellite models, see ICOM radios.

The IC-9700 is full duplex in satellite mode: Main carries the downlink and Sub the uplink. OscarWatch drives both over CI-V on the rear USB port (or over network control for frequency and mode only). USB audio from the same lead is what most stations use for SSB, CW receive, FT4, and recording.

Before you start

  • Install Icom’s USB driver from the Icom support site (Firmware / Software). After a Windows install you usually see two COM ports plus a USB audio device; pick the CI-V port in OscarWatch, not the wrong sibling port.
  • Leave HRD, WSJT-X rig control, RS-BA1, wfview, and similar programs closed so nothing else holds the port.
  • For cross-band satellites (typical linear or FM transponders), uplink and downlink must be on different bands. That is what satellite mode is for on the 9700.

Screenshot placeholder: Windows Device Manager showing the IC-9700 CI-V COM port and USB audio device after the Icom driver is installed.

CI-V on the radio (USB)

Open MENU » SET » Connectors » CI-V. Match OscarWatch to these items (paths and names are from the IC-9700 instruction manual and CI-V reference):

Radio menu item Suggested value Why
CI-V Address A2h (default) Must match CI-V address (hex) in OscarWatch (A2 unless you changed the radio).
CI-V Transceive ON (default) OscarWatch docs call this CI-V TRN. With transceive on, the radio echoes CI-V traffic correctly.
CI-V USB Port Unlink from [REMOTE] Lets the rear USB port run CI-V at full speed. Required for PC control over USB (per CI-V reference note 8).
CI-V USB Baud Rate 115200 (or Auto) OscarWatch defaults to 115200 for the IC-9700. If you pick a fixed rate on the radio, use the same number in Settings.
CI-V USB Echo Back ON Recommended for USB CI-V control software.

The REMOTE jack uses CI-V Baud Rate on the first CI-V screen (often 19200 max). That path is for a separate CI-V cable, not the USB setup above.

Screenshot placeholder: MENU » SET » Connectors » CI-V, second page, with CI-V USB Port, CI-V USB Baud Rate, and CI-V USB Echo Back visible.

OscarWatch: Settings → Radio

  1. Rig type: ICOM IC-9700.
  2. Connection: Serial (USB) unless you use network control (CI-V only; keep USB for audio).
  3. COM port: the IC-9700 CI-V port (Device Manager on Windows; stable by-id path on Linux — see Linux serial ports).
  4. Baud rate: 115200 unless you chose another CI-V USB Baud Rate on the radio.
  5. CI-V address (hex): A2 unless you changed CI-V Address.
  6. IC-9700 model: choose IC-9700, Japan IC-9700, or Japan IC-9700S from the 144 MHz rating on the label. CI-V cannot tell them apart; this matters for FT4 power limits (see Power and good practice).
  7. Enable rig control and Save.

Leave Dual radio off when the 9700 is your only rig. The 9700 already receives and transmits on different bands in satellite mode, so you do not need a second radio for full duplex.

Dual radio (optional)

The IC-9700 can also be one leg of a dual-radio station (for example TS-990S on receive and 9700 on transmit). OscarWatch then leaves satellite mode off on the 9700 and tunes Main only. Enable Settings → Radio → Dual radio, assign downlink and uplink types and ports, and read ICOM dual radio.

Satellite mode on the IC-9700

Cross-band satellites need satellite mode on the radio:

  • MENU » SATELLITE, then touch [SATELLITE] for one second to enter satellite mode (touch again for one second to leave). The manual describes copying the current frequency into the satellite VFO when you enter.
  • In satellite mode, Main is the downlink (receive) band and Sub is the uplink (transmit) band. Touch MAIN or SUB on the screen to select which band you are adjusting with MAIN DIAL.

OscarWatch turns satellite mode on over CI-V when a normal cross-band pass starts, puts downlink on Main and uplink on Sub, and sets modes and CTCSS as needed. You do not need to enter satellite mode by hand before every pass if CAT is enabled.

Receive-only passes (ISS SSTV, beacons with uplink 0 in the database) are different: OscarWatch turns satellite mode off and tracks Main only. See receive-only overview.

Satellite mode expects different bands for uplink and downlink (for example 2 m down and 70 cm up). OscarWatch sets frequencies for the satellite you selected; the radio must already be in a sensible satellite layout.

Screenshot placeholder: IC-9700 in satellite mode with Main showing a 2 m downlink and Sub showing a 70 cm uplink.

Hear the downlink (Sub AF and squelch)

A common support theme is “no audio on the downlink” when the operator is actually listening to the wrong band control or Sub audio is muted.

  • Main = downlink audio you want for SSB, FM, FT4 receive, and recording. Sub is the uplink chain.
  • The upper AF RF/SQL control is for Main; the lower control is for Sub. Push the control to select Main or Sub, then adjust the inner knob for volume and the outer ring for RF gain and squelch.
  • If Sub band receive is muted while you transmit, check MENU » SET » Function » Sub Band Mute (TX) — turn Speaker/Phones, USB, and LAN OFF if you need to hear Sub audio while keying (the manual’s troubleshooting chart points here when no sound is heard).
  • For USB audio to the PC, MENU » SET » Connectors » USB AF/IF Output: Output Select AF. For weak signals, AF SQL OFF (Open) sends audio regardless of squelch; ON follows the radio squelch.

OscarWatch keeps you on Main while you spin the dial to hunt SSB on linear satellites. Uplink (Sub) CAT waits so the radio does not jump to Sub; see spinning the dial and Settings → Radio → Uplink CAT wait after dial (default 2500 ms).

Scope and panadapter

The built-in spectrum scope shows one band at a time. Open MENU » SCOPE (or use M.SCOPE), then touch the MAIN/SUB band icon on the scope screen to switch between Main (downlink) and Sub (uplink) spectra.

While hunting a downlink, show Main. When checking where your uplink sits in the passband, switch to Sub.

Screenshot placeholder: SCOPE screen with the MAIN/SUB band icon highlighted.

What OscarWatch does during a pass

When rig control is on and you track a satellite:

  • Satellite mode on; Main downlink, Sub uplink.
  • Doppler updates on both VFOs, with your offsets and Doppler tuning choices.
  • SSB / CW / FM voice modes on the database set the usual ICOM modes. DATA-USB, DATA-LSB, and DATA-FM (for example FT4) select USB-D / LSB-D / FM-D on the IC-9700 (the driver turns data mode on with CI-V after the base mode, because mode set command 0x26 is not available in satellite mode).
  • Uplink CTCSS when the transponder requires it.
  • Receive-only modes turn satellite mode off and tune Main only.

OscarWatch does not drive the scope over CAT for display band selection; use the radio’s MAIN/SUB icon on the scope screen when you need it.

When you disconnect or quit, OscarWatch clears uplink tone, turns satellite mode off, and leaves Main selected — but only if OscarWatch turned satellite mode on. Untick Turn satellite mode off when OscarWatch closes in Settings → Radio if you prefer the radio to stay in satellite mode.

Modes (SSB, CW, FM, FT4 and data)

Pick the mode in the frequencies panel for the satellite transponder. OscarWatch sends the matching mode to both Main and Sub where the database specifies.

Database mode On the IC-9700 (single radio, satellite mode)
USB / LSB / CW Voice sidebands on Main and Sub as appropriate. Linear CW can follow Settings → Radio → Linear CW: keep receive in USB/LSB (split-style CW on linear birds).
FM / FMN FM on both legs when required.
DATA-USB / DATA-LSB USB-D / LSB-D for digital audio through USB.
DATA-FM FM-D when the database says so.

For FM satellites, turn on the radio’s repeater tone / tone squelch if the transponder needs CTCSS; OscarWatch sets uplink tone when the database includes it.

Audio for FT4, SSTV, and recording

The IC-9700 exposes a USB soundcard when the Icom driver is installed. In OscarWatch FT4 Settings → Soundcards, choose that device for Input (downlink) and Output (modulation to the transmitter). PTT method CAT is the usual choice with USB CI-V.

While FT4 is open, pass recording pauses so FT4 can use the receive device. Configure Settings → Recording with the same USB input when you want archives outside FT4.

For CW receive, connect USB audio to the PC and use OscarWatch CW. For CW transmit, the IC-9700 keys from text over CI-V; see CW keyer.

Troubleshooting

Symptom Things to check
No CAT, wrong frequencies Wrong COM port (two ports appear — confirm which is CI-V in port properties). CI-V address not A2. Baud mismatch. Another program holding the port.
CAT works but audio does not USB audio device selected in Windows or in FT4 / Recording settings. AF SQL on USB output. Squelch closed on Main (downlink).
Downlink silent on FM/SSB Listening on Sub by mistake — select Main. Sub Band Mute (TX) on. Lower AF RF/SQL squelch on Main.
Uplink late after tuning dial Normal until Uplink CAT wait after dial elapses (default 2500 ms).
Frequency snaps back while hunting Short settle after CAT; see Doppler tuning and troubleshooting (ICOM Main/Sub section).
Radio stuck on Sub Resume tracking if Standby is on; toggle satellite mode on the radio; see Problems?.
FT4: radio keys late in slot IC-9700 CAT can be busy on Main and Sub; OscarWatch leads Doppler CAT before transmit slots — see FT4.
Network control fails Only one remote client at a time — close RS-BA1, wfview, and similar. See network control.

After using another rig on the same USB lead, quit OscarWatch, unplug and replug USB, and restart if CI-V stops responding.

Related topics

OscarWatch
OscarWatch
Toggle sidebar