Dual Yaesu FT-817 (two radios)

Two Yaesu FT-817 or FT-818 radios make a practical cross-band satellite station: one receiver for the downlink, one transmitter for the uplink, each on its own band. OscarWatch treats them as Dual radio legs. You hear the passband while you transmit, which a single FT-817 cannot do on its own.

OscarWatch does not list the FT-817 or FT-818 as a single-rig type. If you own one FT-817 today, you still need a second radio (another FT-817, an IC-706, an SDR downlink, and so on) for transmit and receive at once. This page is the full setup when both legs are FT-817 or FT-818 radios. For other Yaesu models in dual mode, see Yaesu radios.

For shorter notes shared with the FT-818, see also Yaesu dual radio and DIG mode on that page.

Tracker version: The full DATA-USB / DATA-LSB / DATA-FM jack routing (DIG, PKT, and menu #26 sideband) described on this page ships in OscarWatch Tracker v1.1.9 (it is not in the v1.1.8 download). On v1.1.8 or older, catalogue data modes may stay on voice USB / LSB over CAT even when you set #26 for the DATA jack.

What you are building

Piece Role
Downlink radio Receive only during the pass. OscarWatch updates its frequency for Doppler.
Uplink radio Transmit. OscarWatch updates its frequency and sends CTCSS when the satellite needs it.
Two CAT cables One USB serial port per radio. CAT does not share one port between two rigs.
Antennas Cross-band birds need a downlink antenna on the RX band and an uplink antenna on the TX band.

Each FT-817 has one receiver. In dual mode OscarWatch uses one main VFO per radio (no satellite CAT mode and no split on the Yaesu leg). That is why two physical radios are the right layout.

CAT wiring (CT-62 or equivalent)

  1. Plug a CT-62 (or equivalent USB CAT interface) into the rear ACC jack on each radio. The factory manual describes the CT-62 as the CAT cable from the ACC jack to the computer.
  2. Connect each interface to its own COM port (or stable device path on Linux). Do not run both radios from one serial adapter.
  3. Leave rotator and GPS on other ports if you use them. See Radio and rotator and Linux serial ports.

OscarWatch speaks Yaesu CAT at 8N2 (8 data bits, no parity, two stop bits), in five-byte frames. The serial speed must match menu #14 on that radio.

One program per port: Close other applications that might hold either COM port before you start OscarWatch. See USB serial adapters if CAT is flaky.

Menu settings on each radio

Repeat these steps on both FT-817 or FT-818 sets. Values can differ per radio only where noted (for example baud rate if you choose different speeds).

Menu #14 CAT RATE

  1. Hold F for one second to enter the menu.
  2. Turn SEL to menu #14 (CAT RATE).
  3. Turn DIAL to 4800, 9600, or 38400 bps.
  4. Hold F to save.

OscarWatch suggests 4800 on each leg (the Tracker default baud for FT-817/818). 38400 also works if you match it in Settings.

OscarWatch serial format

In Settings → Radio, set the baud rate for the downlink and uplink legs to the same value as menu #14 on that physical radio. Use 8N2 on the adapter; the FT-817 manual specifies two stop bits for CAT.

Menu #26 DIG MODE (FT4 and other DATA-USB / DATA-LSB)

When you work DATA-USB or DATA-LSB transponder modes (for example FT4), OscarWatch selects DIG over CAT so audio uses the rear DATA jack. The radio does not switch USER-U / USER-L over CAT; you set that once on the front panel:

  • Menu #26 DIG MODE → USER-U for DATA-USB (typical FT4).
  • Menu #26 DIG MODE → USER-L for DATA-LSB.

There is no USER-FM on the FT-817 or FT-818 for digital work. Plain USB, LSB, and FM stay voice modes on the front RJ-45 microphone jack.

Menu #40 PKT RATE (ISS packet and DATA-FM)

For PKT mode on the DATA jack (see below), the manual uses menu #40 to choose 1200 or 9600 bps RF packet rate. ISS packet is 1200 bps; set #40 to 1200 on the radio you use for Terminal uplink when the pass mode is DATA-FM.

Optional DIG menus #24 DIG DISP and #27 DIG SHIFT are described in the manual for RTTY-style offsets. For FT4-style sound-card work, operators usually leave both at 0 Hz (USER-U / USER-L with no offset).

OscarWatch: enable Dual radio

  1. Open Settings → Radio.
  2. Tick Dual radio.
  3. Downlink: rig type Yaesu FT-817 or Yaesu FT-818, COM port, baud (match menu #14 on that radio).
  4. Uplink: same rig types if both radios are FT-817/818, different COM port, baud matched on that radio.
  5. Save and connect. The status line should show both legs when ports are open.

You may put either physical radio in the downlink or uplink slot. What matters is that the downlink leg is the radio wired for receive audio and the uplink leg is the one you key for transmit.

Mixed pairs (FT-817 downlink + IC-706 uplink, and so on) use the same Dual radio screen; only the rig types differ. See ICOM dual radio.

Which radio on which band

OscarWatch takes uplink and downlink bands and modes from the satellite transponder you select. At pass start it tunes each leg to the right band on that radio.

Typical Mode V/U linear or FM satellites:

  • Downlink radio → 70 cm (or whatever the database lists as RX).
  • Uplink radio → 2 m (or the listed TX band).

You can also run two FT-817 radios as both legs on other pairs, for example AO-07 Mode A with an FT-817 on 10 m downlink and a 2 m-capable radio on uplink (the second leg can be another FT-817 on 2 m). OscarWatch does not enforce band choice in software; the radio must cover the frequency you ask for.

If you swap which physical radio sits in the downlink or uplink row in Settings, swap the CAT cables on the PC too, or the frequencies will go to the wrong box.

Doppler and the frequency panel

With Full Doppler in the frequencies panel (the default for most satellites):

  • Downlink radio receives Doppler corrections.
  • Uplink radio receives Doppler corrections and uplink CTCSS when the pass needs it.

Use Full unless you deliberately want TX-only or RX-only behaviour (uncommon on a dual FT-817 desk).

On linear USB / LSB / CW, you can spin the downlink dial to hunt the passband. OscarWatch pauses downlink CAT while you tune, then resumes. The uplink radio keeps tracking Doppler on the other leg. See spinning the dial.

On FM, OscarWatch may lock the downlink dial over CAT while tracking. Use Pause CAT in Settings if you need to tune the FM downlink by hand.

DATA-USB, DATA-LSB, and DATA-FM use continuous Doppler updates (no FM-style threshold gate on the digital modes). Lead Doppler and adaptive threshold still follow Doppler tuning.

Thresholds: FM and SSB/CW thresholds under Settings → Radio apply per leg from the downlink mode. Start with the defaults in Doppler tuning and adjust only if CAT feels too busy or too sluggish.

Modes OscarWatch sets over CAT

From OscarWatch Tracker v1.1.9, OscarWatch maps catalogue modes to Yaesu CAT as below. On v1.1.8 or older, DATA-* modes may not select DIG or PKT during a pass.

Catalogue mode Yaesu mode over CAT Audio jack
USB, LSB, FM, CW Same mode on the mic side Front RJ-45 microphone jack
DATA-USB, DATA-LSB DIG (sideband from menu #26) Rear DATA jack
DATA-FM PKT Rear DATA jack

OscarWatch reads DATA-FM on the transponder database as packet FM for the DATA jack (for example ISS digipeater work in OscarWatch Terminal). Set menu #26 for DIG modes before an FT4 pass; set menu #40 for 1200 bps packet when you use PKT.

Full duplex with two radios

On a cross-band satellite, the downlink and uplink are on different bands. With two FT-817 radios you can listen on the downlink radio while the uplink radio transmits. That is the main reason for this station layout.

A single FT-817 has one receiver on one band at a time. It cannot hear its own downlink while it transmits on another band in the way a two-radio desk can. OscarWatch will not offer the FT-817 as a lone full-duplex satellite rig.

For same-frequency packet (ISS on 145.825 MHz), the link is half duplex even with two radios on the bench. Terminal switches between transmit and listen on the uplink leg; you do not get a separate full-duplex audio path like a linear transponder.

Audio paths

Plan audio per radio:

Task Radio Jack Notes
SSB/FM voice RX Downlink Front mic jack or headphone from AF Recording and voice tools use your chosen input device in Settings
SSB/FM voice TX Uplink Front mic jack PTT on the uplink radio or via your interface
FT4 RX Downlink Rear DATA out → PC Radio in DIG, menu #26 USER-U (or USER-L)
FT4 TX Uplink PC → rear DATA in Same DIG setup on the uplink radio; OscarWatch FT4 keys the uplink
ISS packet Uplink (typical) Rear DATA jack, PKT mode Half duplex in Terminal; see Terminal audio

The manual states that during digital or packet work from the DATA jack, the front microphone input is cut off while the radio transmits from the data port. That avoids a live microphone on the desk when the DATA jack is in use.

Use the radio DATA port level (not the speaker socket) for packet and FT4 where you can. The DATA receive level is fixed on the jack and does not follow the AF knob, which makes modem levels steadier.

OscarWatch FT4 and Terminal share sound-card capture settings under Settings → Recording; pick the interface wired from the downlink DATA or line output for decode.

Before your first pass

  1. Both radios powered, antennas connected, menu #14 matched in OscarWatch per leg.
  2. Dual radio on, both COM ports connected, Full Doppler selected for the satellite mode.
  3. For FT4: menu #26 USER-U on both legs if both use the DATA jack, OscarWatch Tracker v1.1.9, transponder mode DATA-USB in the frequency panel.
  4. Select the satellite, press Resume tracking if needed, and watch the frequency panel Radio row move on both legs.

Troubleshooting

Symptom Things to check
Only one leg connects Wrong COM port, baud mismatch on menu #14, or another program holding a port. Each radio needs its own port.
Downlink frequency stuck, uplink moves Doppler set to TX-only instead of Full, or downlink CAT paused. Use Full in the frequency panel. On linear SSB, spin the downlink, pause ~1 s so passband trim is captured. See FT-817 / FT-818: downlink stuck, uplink tracks and Yaesu radios.
FM downlink will not tune Expected while CAT tracks FM; use Pause CAT or tune before the pass.
Radio stops answering CAT Power-cycle the affected FT-817. Avoid swapping USB ports mid-pass. Try a higher CAT delay on that leg. Cheap USB serial chips can drop commands; prefer FTDI where possible.
FT4 silent on DATA jack Tracker still on v1.1.8 or older (no DIG over CAT yet), menu #26 not USER-U, or pass mode still USB instead of catalogue DATA-USB.
No ISS packet audio Radio not in PKT, menu #40 not 1200, or Terminal duplex set wrong (ISS wants half duplex on one band).
Heavy CAT / radio freeze Lower Doppler thresholds only after checking baud and delay. One OscarWatch instance per pair of ports.

More general serial and dual-radio notes live under Problems?.

Related guides

OscarWatch
OscarWatch
Toggle sidebar