Yaesu FT-818 / FT-818ND
The FT-818 and FT-818ND are compact HF/VHF/UHF portable transceivers. OscarWatch talks to them over Yaesu five-byte CAT (same protocol as the FT-817). The radio has one receiver, so you either run one FT-818 for half-duplex satellite work, or two FT-818s in Dual radio mode so you can listen on one band while transmitting on another.
Tracker version: Single-radio FT-818 support and the full DATA-USB / DATA-LSB / DATA-FM jack routing described below ship from OscarWatch Tracker v1.1.9 (they are not in v1.1.8 or older). On v1.1.8 or older, FT-818 appears only under Settings → Radio → Dual radio. The FT-817 stays dual-radio only; see the general Yaesu dual radio section until the dedicated FT-817 guide lands.
What you need
- CAT cable to the rear ACC jack. Yaesu CT-62 (serial) or SCU-17 (USB interface plus CT-62-style connection) is the usual choice.
- A separate COM port for each FT-818 when you use Dual radio (and a third port if you add a rotator).
- Menu #14 CAT RATE on the radio set to match OscarWatch (suggested 4800 baud; 9600 and 38400 also work).
- OscarWatch expects 8 data bits, no parity, two stop bits (8N2) on the serial link, matching the FT-818ND operating manual.
- Close other programs that might hold the COM port before you track a pass.
Screenshot placeholder: rear panel showing ACC and DATA jacks.
Radio menus (CAT and data)
| Menu | Name | What to set |
|---|---|---|
| #14 | CAT RATE | 4800, 9600, or 38400 bps to match OscarWatch (default on the radio is 4800). |
| #26 | DIG MODE | USER-U for catalogue DATA-USB (for example FT4 on the DATA jack), or USER-L for DATA-LSB. OscarWatch does not change this over CAT. |
| #40 | PKT RATE | 1200 or 9600 bps packet rate on the DATA jack when you use external packet hardware. For OscarWatch Terminal on DATA-FM satellites, set 1200 for typical ISS-style packet unless your satellite notes say otherwise. |
To open the menu: hold F for one second, turn SEL to the item, turn DIAL to the value, then hold F again to save.
The FT-817/818 CAT system has no satellite mode and no USER-FM DIG preset. OscarWatch does not turn on hardware split for a pair of FT-818 legs in Dual radio; each radio keeps one main VFO.
Settings → Radio
Single FT-818 (half-duplex)
- Leave Dual radio off.
- Rig type: Yaesu FT-818 (from OscarWatch Tracker v1.1.9).
- COM port: the port for the ACC/SCU-17 interface.
- Baud rate: match menu #14 (OscarWatch suggests 4800).
- Region: EU or USA (affects FM tone / CTCSS behaviour on the uplink).
- Save, then track a pass with Resume tracking.
Screenshot placeholder: Settings → Radio with FT-818 selected as the single rig type.
Dual radio with two FT-818s
- Tick Dual radio.
- Downlink: Yaesu FT-818, COM port and baud for the receive radio.
- Uplink: Yaesu FT-818 (or another supported uplink rig), COM port and baud for the transmit radio.
- Match menu #14 on each radio to that leg’s baud in Settings.
- Use Full Doppler in the frequency panel unless you know you need RX-only or TX-only.
A common layout is FT-818 on downlink and a 2 m-capable radio on uplink; two FT-818s (one on 2 m RX, one on 70 cm TX, or the reverse) is also supported. For AO-07 Mode A, an FT-818 on 10 m downlink with a 2 m uplink is supported (there is no software band gate in the driver).
You can also mix an FT-818 with ICOM, Kenwood, or SDR downlink legs; see those pages for the second radio.
Screenshot placeholder: Dual radio with FT-818 on downlink and uplink.
Single-radio limits (half-duplex)
One FT-818 is a good fit for FM voice cubesats and half-duplex work (including DATA-FM / packet on one band), not for listening to your own downlink while you transmit.
- The radio has one receiver. While you are keyed, you cannot hear the satellite downlink on the same radio.
- OscarWatch still applies Doppler to receive and transmit frequencies over CAT, but full-duplex monitoring of your own signal needs Dual radio or a full-duplex rig such as an ICOM satellite radio or FT-847.
- OscarWatch does not read or set RF power on the FT-818; set watts on the front panel (up to 6 W on external 13.8 V per the FT-818ND manual, or 2.5 W on internal batteries).
For linear SSB passes where you want to hunt the passband and hear yourself in the transponder, use two radios (Dual radio) instead of one FT-818.
What OscarWatch does on a pass
- Sets modes from the satellite catalogue (USB, LSB, FM, DIG, PKT, and so on).
- Sends Doppler corrections on the correct leg: one radio in single mode; downlink and uplink drivers in Dual radio.
- Applies your RX and TX offsets.
- Sends uplink CTCSS when the satellite needs it (Dual radio: on the uplink leg only).
- On linear USB/LSB/CW, passband trim on the downlink dial is supported in Dual radio (spin the RX radio; uplink keeps tracking). See spinning the dial.
- On FM, OscarWatch may lock the front-panel dial over CAT while tracking. Use Pause CAT in Settings if you need to tune by hand.
Use Full Doppler in the frequency panel for normal cross-band work. DATA-USB, DATA-LSB, and DATA-FM ignore Doppler lead; voice and FM follow the usual Doppler tuning settings.
In Dual radio, if the downlink frequency looks stuck while the uplink moves, check that Doppler is Full, not RX-only or TX-only. On linear SSB, spin the downlink, pause about one second so passband trim is captured, then let CAT resume. Details are in troubleshooting.
Modes and audio jacks
OscarWatch maps catalogue modes to the correct Yaesu mode over CAT. Audio routing follows the radio hardware:
| Catalogue mode | CAT mode | Audio jack |
|---|---|---|
| USB, LSB, FM (voice) | USB / LSB / FM | Front MIC jack (RJ-45) |
| DATA-USB, DATA-LSB (for example FT4) | DIG | Rear DATA jack; set menu #26 to USER-U or USER-L on the radio |
| DATA-FM (for example ISS packet in Terminal) | PKT | Rear DATA jack |
Plain voice USB and LSB always stay on the microphone jack. DATA-FM does not use a USER-FM menu choice on the FT-818; OscarWatch selects PKT for the DATA jack.
For FT4 or other soundcard data through a Digirig (or similar), cable audio and PTT to the rear DATA jack, set #26 DIG MODE to USER-U (or USER-L for LSB data), and pick a satellite mode of DATA-USB or DATA-LSB in OscarWatch. See the FT4 guide for pass workflow.
For OscarWatch Terminal on ISS-style DATA-FM, use the DATA jack for the built-in modem audio path; Terminal’s half-duplex behaviour matches the single receiver (it waits for a clear channel before transmit). See Terminal duplex settings.
FT-818 and FT-817
For OscarWatch CAT, the two radios behave the same: the FT-818 driver uses the same protocol as the FT-817.
| Topic | FT-817 | FT-818 / FT-818ND |
|---|---|---|
| OscarWatch (v1.1.9+) | Dual radio only | Single radio (half-duplex) or Dual radio leg |
| CAT menus for this guide | #14, #26 (same numbers) | #14, #26 (verified FT-818ND manual) |
| Bands | HF/6 m, 2 m, 70 cm | HF/6 m, 2 m, 70 cm |
| RF power (manual) | Model-dependent | Up to 6 W on external 13.8 V; 2.5 W on internal batteries |
OscarWatch does not quote factory-spec sensitivity or filter options; rely on the Yaesu manual for hardware differences unrelated to CAT.
Receive-only (beacons, SSTV)
When uplink is 0 in the database, OscarWatch corrects the downlink only. Layout follows the single- or dual-radio driver. See receive-only overview.
Troubleshooting
| Symptom | Things to check |
|---|---|
| No CAT | Menu #14 matches Settings; 8N2 on the COM port; correct ACC/SCU-17 port; only one program using the port. |
| Digital modes silent or wrong jack | Voice modes on the MIC jack; DATA-* modes need DIG or PKT and the DATA jack. Set #26 to USER-U / USER-L for FT4. |
| Downlink stuck, uplink tracks (Dual radio) | Full Doppler; on linear SSB, passband trim on the downlink (pause ~1 s after finding the signal). |
| FM dial will not move | Expected while tracking; use Pause CAT or switch to USB/LSB for manual tuning. |
| Radio stops answering CAT | Wrong baud, heavy traffic from another app, or a clone USB adapter. Power-cycle the radio; try CAT delay under Settings → Radio. |
| FT-818 missing from single-radio list | You need OscarWatch Tracker v1.1.9 or newer. On v1.1.8 or older, enable Dual radio or see general troubleshooting. |
Tip: Prefer a genuine FTDI USB serial adapter or the radio’s own USB path. Cheap clones often cause missed CAT commands; see USB serial.
Further dual-leg notes (baud, ports, stuck downlink) also appear under Yaesu dual radio and troubleshooting.