OscarWatch FT8

OscarWatch FT8 is the same modem window as OscarWatch FT4, running FT8. It listens, sends the messages, switches the radio to transmit, keeps you on frequency, and saves a finished contact to the logbook. You can have a go without running WSJT-X.

QO-100 is the satellite most people use for FT8. Any other linear satellite works the same way when its catalogue has an FT8 transponder, including a custom row you add yourself.

On this page

What FT8 is

FT8 is a short contact made from a handful of fixed messages. The computer turns each message into a tone. Time is split into slots of 15 seconds. You send in one slot and listen in the next, so one exchange takes 30 seconds. From the first call to the goodbye is usually about two minutes.

You and the other station take opposite slots, so you are never transmitting at the same time. Those two turns are called even and odd. When you answer someone, OscarWatch picks the turn they are not using.

The messages look the same as FT4: a CQ with a grid, a signal report, RR73 and 73. Words you will see on the FT4 page covers them, including callsigns in angle brackets.

A linear satellite repeats a whole slice of frequencies. You can listen while you transmit, so you hear your own signal come back. OscarWatch shows that copy as Echo, and uses it to nudge your transmit frequency until the echo sits in the right place. That trim is stored for the FT8 transponder on its own, separate from any FT4 trim on the same satellite.

Every slot starts on an exact second, so the PC clock needs to be right to about half a second. Turn on Windows time synchronisation, or use a tool such as Meinberg NTP, before a pass.

No internet in the field? Use GPS time for FT4 slot timing in Settings → Integrations → GPS also times FT8 slots. The setting name still says FT4. See Clock source.

Which satellites

Open Tools → OscarWatch FT8 when the satellite you are tracking has an FT8 transponder. The menu item is greyed out until it does.

The transponder type is FT8, or FT8 followed by a space or punctuation, such as FT8 Asia or FT8-Asia. Select that row in the satellite panel, or let the menu item select it for you.

The same limits as FT4 apply:

  • the satellite has to be linear. An FM repeater satellite does not let you hear your own signal;
  • FO-29 is blocked. Its licence does not allow this kind of mode;
  • AO-7 is blocked. AMSAT has asked that these modes are not used there;
  • keep the radio at 30 W or less. See Power and good practice.

Until those are satisfied, transmit stays off and the status line says why. You also need a callsign and a locator of at least four characters under Settings → Station. See Before a pass.

Opening the window

  1. Select the satellite on the main window.
  2. Open Tools → OscarWatch FT8. That selects the FT8 transponder, then opens the window. The title reads OscarWatch FT8.
  3. If the window is already open, choosing the menu again brings it forward and switches it to FT8. The decode list and the waterfall clear, so FT4 and FT8 lines never mix.

Tools → OscarWatch FT4, or selecting an FT4 row, switches the same window back to FT4 and retitles it OscarWatch FT4. Only one window can be open.

Audio, PTT, callsign, logbook and the other settings are shared. You set them once. Press Settings in the window. The pages are described under Settings.

A contact

The FT4 video shows how to find your own signal on the waterfall. The traces and the echo look the same on FT8. The slots are 15 seconds instead of 7.5.

  1. Open Tools → OscarWatch FT8. The waterfall starts, and the status says Listening.
  2. Press Settings. On Soundcards, pick the input (audio from the radio) and the output (audio to the radio). On PTT, pick how the radio is switched to transmit. CAT is the usual choice when the radio has a USB control lead.
  3. Press Tune. A steady tone goes out. Set TX level so the radio's ALC meter barely moves. Keep the power at 30 W or less. Press Tune again to stop.
  4. Watch the list. A station calling anyone looks like CQ EA1ABC IN63.
  5. Click their line to answer, or press CQ to call yourself. OscarWatch fills in the TX message, chooses the right slot, and turns transmit on.
  6. Leave it to run. Your sends are marked TX. Your signal back from the satellite is marked Echo.
  7. When both signal reports have been exchanged and both stations have sent 73, the contact is saved to the logbook with the mode FT8. RR73 counts as that station's 73.

Press Halt Tx at any time to stop at once. How to read each line is under Reading a message.

What changes from FT4

FT4 FT8
Slot 7.5 seconds 15 seconds
Menu Tools → OscarWatch FT4 Tools → OscarWatch FT8
Window title OscarWatch FT4 OscarWatch FT8
Logbook, PSK Reporter and OscarWatch.org spots FT4 FT8
Waterfall slot lines Every 7.5 seconds Every 15 seconds
Echo trim Stored for the FT4 transponder Stored for the FT8 transponder

The radio is updated once for each 15 second slot, then held still, so it is not being tuned while a message is going out. Select another transponder, such as the SSB row, and the hold releases straight away. See When the hold applies, and going back to SSB.

FT8 decodes the slot directly. The extra search for a drifting signal, and the weak-reply hints that show as AP on FT4, are used for FT4. The Modem page is shared, so Hint weak replies (AP) is still on the settings page while you are on FT8.

The Reporting tick is still labelled Send FT4 spots to OscarWatch.org, because the two modes share that setting. While the window is on FT8, each spot is stored as FT8 and the time is rounded to the 15 second slot. Your own transmissions and echoes are never sent. See Satellite spots.

What stays the same

These parts of the FT4 guide apply while the window is on FT8:

OscarWatch
OscarWatch
Toggle sidebar