CW keyer
Reading Morse is a separate window: Tools → OscarWatch CW. That guide is OscarWatch CW. This page is about sending.
The OscarWatch Logbook can send CW for you. Twelve message buttons sit between the QSO entry row and the recent QSO list, in the style of contest loggers such as N1MM. Each button sends a message built from macros such as your callsign, their callsign and the report, so a whole satellite CW contact can run from the function keys while you tune.
Turning it on
- Open Tools → OscarWatch Logbook, then Settings from the logbook menu.
- Open the CW keyer tab and tick Show the CW keyer in the logbook.
- Check the Keying section (see How OscarWatch keys the radio) and edit the messages if you like.
- Press Save.
The button row appears only when the station control mode is CW (or CW-R). Switch the focused satellite to a CW mode, or use Voice / CW on the frequency panel, and the row shows up above the recent QSO list.
Sending messages
- Click a button, or press F1 to F12 while the logbook window is active. F1 is the first button, F12 the last.
- The button that is sending turns red. Pressing another button stops the current message and sends the new one.
- Press Esc or Stop to abort straight away.
- The status bar shows what is being sent, then Sent when it finishes. If a message uses a macro OscarWatch does not know, it is left out and named in the status bar.
- A button with no message does nothing. Its tooltip reminds you to add one in Logbook settings.
Messages are built from the entry row at the moment you press the key, so type the callsign and reports before sending a message that uses them.
Default messages
| Key | Name | Message |
|---|---|---|
| F1 | CQ | CQ SAT DE {MYCALL} {MYCALL} |
| F2 | Call | {CALL} |
| F3 | Report | {CALL} {SENTRST} {MYGRID} |
| F4 | My call | {MYCALL} |
| F5 | Grid | {MYGRID} |
| F6 | TU | TU {MYCALL} SK |
F7 to F12 start empty. Give each button a short name (up to 12 characters) and a message (up to 200 characters) in the Messages list on the CW keyer tab.
Macros
| Macro | Sends |
|---|---|
{MYCALL} or * |
Your callsign from the current logbook |
{CALL} or ! |
The callsign in the entry row |
{SENTRST} |
RST sent |
{SENTRSTCUT} |
RST sent with cut numbers, so 599 is sent as 5NN |
{RCVDRST} |
RST received |
{GRID} |
Their grid from the entry row |
{MYGRID} |
Your four-character grid from the logbook |
{NAME} |
Their name from the entry row |
{SAT} |
The focused satellite |
{AR} {SK} {BT} {KN} |
Prosigns, sent without a gap between the letters |
Macros are not case sensitive. Everything else in a message is sent as typed, in capitals.
Speed
The WPM box next to Stop sets the speed from 5 to 60 words per minute. Changes are saved straight away and apply to the next message. The same value is on the CW keyer tab. OscarWatch uses standard PARIS timing.
How OscarWatch keys the radio
The Keying section on the CW keyer tab shows your uplink radio and how OscarWatch will key it. With dual radios, the uplink radio is used.
| Uplink radio | Method |
|---|---|
| Kenwood TS-2000, TS-590S, TS-590SG, TS-890S, TS-990S | Text over CAT (KY). See Kenwood. |
| Icom IC-9700, IC-705, IC-7300, IC-7100, IC-905 | Text over CI-V (0x17). See Icom. |
| Any other radio | A COM key line (DTR or RTS). See COM key line. |
Kenwood
Kenwood radios form the Morse themselves from text sent with the KY command, so no keying cable is needed. Put the radio in CW mode with break-in on. OscarWatch sets the radio's keyer speed with KS when you change WPM. Stop clears the radio's CW buffer.
Icom
The IC-9700, IC-705, IC-7300, IC-7100 and IC-905 accept CW text over CI-V command 0x17 and key it with their internal keyer. Put the radio in CW mode with break-in on. The Icom keyer runs from 6 to 48 WPM, so speeds outside that range are sent at the nearest limit. Long messages are sent in pieces of up to 30 characters.
If you would rather key the radio with a cable, tick Use a COM key line instead of CI-V text and set up a COM key line.
COM key line
For every other radio, OscarWatch keys a serial handshake line itself and times every dot and dash. Connect the line to the radio's key jack through a keying interface (a transistor or opto-isolator), put the radio in CW mode and turn break-in on.
- Key line: choose DTR or RTS.
- Use a separate COM port for the key line: tick this when the keying interface is on its own COM port, then pick the port under CW key COM port. Press Refresh after plugging in a USB adapter. Leave it unticked to key the line on the radio's own CAT port.
Some things to check:
- Keying on the CAT port needs rig control turned on. With rig control off, only a separate COM port can key CW.
- The Yaesu FT-991, FT-991A and FTX-1 use RTS on the CAT port for flow control. Use DTR, or a separate COM port.
- The separate port must not be the radio, rotator, or GPS port. OscarWatch tells you if it is. It may be the same port FT4 or Terminal uses for separate PTT, for example when a radio's second USB port puts PTT on RTS and CW on DTR.
- Close any other application that has the port open.
Tip: Satellite CW is full duplex. Listen to your own downlink while a message is sending and adjust the TX offset if your signal is off frequency. See RX and TX offsets.
Troubleshooting
- The button row is missing: tick Show the CW keyer in the logbook and make sure the station control mode is CW.
- "The radio did not accept the CW": the radio is not connected, not in CW mode, or does not support CW text over CAT. Check rig control and the radio's mode.
- Nothing is transmitted on a COM key line: check break-in is on, the right line (DTR or RTS) is chosen, and the keying interface is wired to the key jack. Try the other line.
- Keying sounds uneven: close heavy applications, or use the radio's own keyer (Kenwood or Icom text) where it is available.