Kenwood TS-2000 with OscarWatch Tracker
This guide is for satellite operators using a Kenwood TS-2000 as a single full-duplex radio with OscarWatch Tracker (SATL over CAT, Beta). It covers getting the radio itself right as well as the OscarWatch settings, because many on-air problems start on the front panel, not in the app.
If you pair the TS-2000 with a second radio under Dual radio, SATL stays off and only VFO A is tuned. See TS-2000 as a Dual radio leg. Other Kenwood models are on Kenwood radios.
On this page
- Cable and baud rate
- OscarWatch radio settings
- Satellite mode on the TS-2000
- Main and Sub roles
- Sub-receiver audio and squelch
- What OscarWatch does on a pass
- Modes OscarWatch can set
- FT4 and data audio
- Before you track
- Troubleshooting
Who this guide is for
You may be new to satellite mode on the TS-2000 after using SatPC32, a hardware controller, or a different rig. The TS-2000 runs cross-band satellite mode (Kenwood calls this SATL on the display): one VFO pair handles downlink and uplink on different bands. OscarWatch enters and maintains that layout over CAT when you track, but you still need the radio in the right state before the pass.
Cable and baud rate
Connect the rear-panel COM jack to the PC with a 9-pin RS-232 cable (or a USB serial adapter that passes RTS for hardware flow control). OscarWatch uses Kenwood ASCII CAT: commands end with a semicolon, 8 data bits, no parity, one stop bit (8N1), matching the transceiver manual’s PC communication notes for Menu 56.
- On the radio: press [MENU], turn MULTI/CH to Menu No. 56, and set the same baud rate you will choose in OscarWatch (defaults are 9600 in the manual; OscarWatch selects 57600 when you pick Kenwood TS-2000).
- In OscarWatch: Settings → Radio — enable the radio, set Rig type to Kenwood TS-2000, choose the COM port (or type a Linux device path), and set Baud rate to match Menu 56.
Screenshot placeholder: Rear-panel COM jack and a typical USB–serial adapter labelled with the COM port or /dev/serial/by-id/... name.
Leave Hardware RTS (flow control) on unless your cable or adapter does not wire RTS. The TS-2000 often only answers CAT when the PC asserts RTS. If CAT is silent with RTS on, try a full RS-232 cable; if your adapter has no flow control, turn Hardware RTS off in OscarWatch (same guidance as Kenwood radios).
Close other programs that might hold the port (HRD, WSJT-X rig control, another tracking app). On Linux, give the port a stable path — Linux serial ports.
OscarWatch radio settings
| Setting | What to use |
|---|---|
| Rig type | Kenwood TS-2000 |
| COM port | The TS-2000 only (rotator and GPS need their own ports) |
| Baud rate | Match Menu 56 (OscarWatch default 57600) |
| Hardware RTS | On for full cables; off only if the adapter has no RTS |
| TRACE / TRACE REV in SATL | On by default — the radio’s built-in trace tracks with the downlink. Turn off when OscarWatch alone should manage Doppler (recommended with PC tracking). Try both if you are unsure |
| Turn satellite mode off when OscarWatch closes | On by default — OscarWatch sends the SATL exit sequence when you quit or disconnect; untick to stay in SATL on the radio |
| Doppler thresholds | See Doppler tuning; TS-2000 uses the same FM vs SSB/CW threshold logic as other rigs |
The in-app hint under Settings → Radio repeats the essentials: 57600 8N1, select satellite mode on the radio, and leave memory mode off before tracking.
Satellite mode on the TS-2000
Amateur satellites receive on one band and transmit on another. The TS-2000 manual’s satellite chapter describes this cross-band layout. OscarWatch drives SATL over CAT (SA, then FA / FB for frequencies), similar to SatPC32.
On the front panel:
- Press [SATL] to enter satellite mode (the manual’s “Satellite mode” steps start here).
- Prefer VFO operation, not memory recall, on main and sub paths before tracking. OscarWatch also clears memory mode via CAT when needed, but starting in VFO is the most reliable approach.
- Close any menu on the display before you start tracking.
OscarWatch can confirm SATL with SA; after you connect. If confirmation fails, it still Doppler-tracks on FA/FB but shows a warning; check SATL, memory mode, and closed menus, then re-select the satellite. Do not rely on ordinary split (FR/FT) while cross-band SATL is expected — the driver does not fall back to split in that state.
TRACE on the radio vs in OscarWatch
In SATL, the TS-2000’s TRACE function can move the uplink when you tune the downlink (the manual describes Reverse trace and Normal trace). OscarWatch’s TRACE / TRACE REV in SATL checkbox controls whether its SATL entry commands leave TRACE enabled (SA1010110;) or off (SA1010000;). For PC-managed Doppler, turn TRACE off in OscarWatch so the radio does not fight FA/FB updates.
Main and Sub roles
In OscarWatch’s model (and in SATL CAT):
- Main / VFO A (
FA) — downlink (what you listen to). - Sub / VFO B (
FB) — uplink (what you transmit on).
Uplink and downlink must be on different bands for normal cross-band satellites. If your bands are swapped, OscarWatch can exchange FA/FB when the driver detects the wrong layout.
When OscarWatch sets uplink mode or CTCSS, it momentarily selects Sub control in SATL (SA1011110;) so mode and tone land on the uplink VFO, then returns to main control.
Sub-receiver audio and squelch
The TS-2000 has a separate sub-receiver on 144 MHz and 430/440 MHz (FM and AM). In SATL, your satellite downlink is on the main transceiver path; you hear it on the main audio controls, not only on the sub-receiver.
A common mistake: the sub-receiver is ON but squelched closed (no AF from the sub). You may think the downlink is dead when you are simply not listening on the path that has the signal.
- For satellite listening on the main path, use the main AF and squelch as you normally would for SSB, CW, or FM on that band.
- If you do use the sub-receiver for something else (club channel, packet cluster), press the SUB AF control to switch the sub-receiver on or off. The manual describes ADJUSTING THE AF GAIN and ADJUSTING THE SQUELCH for the sub-receiver when
[SUB]control is active. - Before a pass, either turn the sub-receiver off if you do not need it, or open its squelch so it does not hide useful audio while you troubleshoot.
OscarWatch does not remote-control sub-receiver AF or squelch; set them on the radio.
What OscarWatch does on a pass
When you select a satellite and tracking runs with the TS-2000 connected:
- Enters or reaffirms SATL and programmes pass frequencies on
FA/FB, with modes and uplink CTCSS when the transponder needs it (encode on uplink). - Applies Doppler on both legs for cross-band modes, using your offsets and Doppler tuning settings.
- Sends an
FA;read about once per second while tracking (link-hold, SatPC32-style). - Does not set RF power on the radio; you control power on the panel. For FT4, OscarWatch reads power (
PC;) and can limit to 30 W when configured. - On quit or disconnect (if Turn satellite mode off when OscarWatch closes is on), sends
RX;,TO0;,SA0010000;to leave SATL cleanly.
Receive-only (beacons, SSTV — uplink 0 in the database): OscarWatch keeps SATL and Doppler-tracks FA only, leaving FB parked. That differs from ICOM behaviour; see receive-only overview.
Same-band modes (uplink and downlink within 10 MHz, e.g. some packet passes): OscarWatch turns SATL off and uses split (FR0;FT1;) like other non-cross-band passes.
Hunting SSB: use passband trim; Doppler follows your offset. Pause CAT in Settings if you want full manual control for a while.
Modes OscarWatch can set
Over CAT the driver maps transponder modes to Kenwood MD codes: LSB, USB, CW, FM (including FMN / DATA-FM), and AM. OscarWatch sets the mode for the pass on main and sub as needed in SATL.
OscarWatch does not invent modes the codec does not know; if a mode string is unsupported, check the frequency panel and transponder database.
FT4 and data audio
The TS-2000 has no separate “data” USB-D path like an IC-9700. For FT4 and similar:
- Run USB (or the mode the satellite expects) on the uplink and downlink as OscarWatch sets them.
- Route receive audio from the radio to the PC and transmit audio from the PC to the radio through a USB soundcard interface (or the station interface you already use), the same way as for other non-ICOM rigs. See OscarWatch FT4 → Before a pass.
- In the FT4 window, choose CAT for PTT when OscarWatch already holds the COM port. Tick Lower RF power to 30 W in FT4 settings if you want OscarWatch to send
PC030;before transmit. - OscarWatch reads reported power for the FT4 interlock; it does not measure power after an external amplifier.
Before you track
Checklist:
- Menu 56 baud matches OscarWatch; 8N1 on both sides.
- Settings → Radio: Kenwood TS-2000, correct port, Hardware RTS suited to your cable.
- Press [SATL] on the radio; VFO not memory; menus closed.
- Choose satellite and mode in the frequency panel; set offsets if needed.
- Resume tracking and watch the status line for a connected rig and sensible frequencies.
FM satellites: Pick the right CTCSS in the frequency panel when the database lists access tones. OscarWatch sets encode on the uplink; tone decode on the downlink can mute SSB-like signals on FM satellites — use encode-only behaviour as intended for uplink tone.
Troubleshooting
| Problem | Things to check |
|---|---|
| No CAT replies at all | RTS/cable (see troubleshooting → TS-2000); port busy; wrong COM port; baud mismatch with Menu 56 |
| SATL not confirmed warning | Press [SATL]; VFO not memory; close menus; retry satellite selection |
| Downlink silent | Main AF/squelch; wrong band; sub-receiver squelched or not the active path for your downlink; antenna/band select on the radio |
| Uplink wrong band or mode | Cross-band satellite requires different bands; let OscarWatch finish pass init; check frequency panel mode |
| Doppler feels sluggish or jumpy | Doppler thresholds; try TRACE off in OscarWatch; radio TRACE off when PC tracks |
| CAT fights your dial | Pause CAT temporarily |
| Same-band packet pass odd behaviour | Expected: SATL off, split on — see Kenwood radios |
More fixes: Troubleshooting, USB serial adapters, Linux serial ports.