Yaesu FT-847 with OscarWatch Tracker

This page is for operators who run the FT-847 as a single satellite radio with OscarWatch Tracker. It covers the radio front panel and menus, the CAT cable, and what OscarWatch does during a pass. For a shorter feature list and dual-radio use as one leg only, see Yaesu radios.

If you are used to SatPC32 or a hardware satellite controller, the FT-847 is still a satellite rig: you stay in satellite mode for normal cross-band passes, and OscarWatch drives SAT receive and SAT transmit over CAT.

What OscarWatch expects

Item Detail
Rig type Yaesu FT-847 in Settings → Radio (Dual radio off)
Serial format 8N2, five-byte Yaesu CAT (OscarWatch default)
Baud rate 57600 suggested in Settings; must match radio menu #37
CAT port Rear CAT/LINEAR jack via a level converter (for example CT-62)
Satellite layout Cross-band: SAT mode on, downlink on Main (SAT RX), uplink on Sub (SAT TX)
VFO swap over CAT Not supported — band roles follow OscarWatch and the front panel

OscarWatch opens CAT with a session-on command, turns satellite mode on for cross-band transponders, and sends CAT off when you quit or disconnect unless you untick Turn satellite mode off when OscarWatch closes in Settings → Radio.

[Screenshot placeholder: Settings → Radio with FT-847 selected, COM port, and baud rate visible.]

CAT cable and serial port

  1. Use a null-modem (crossed) serial cable between the PC and the CAT/LINEAR jack, with a CT-62 or equivalent level converter on the radio side (OscarWatch shows this hint when FT-847 is selected).
  2. On the radio, open the menu and set #37 CAT RATE to 57600, 9600, or 4800 (factory default is 4800). Pick the same rate in Settings → Radio → Baud rate. When you first choose FT-847, OscarWatch sets 57600 as a starting point.
  3. In OscarWatch, choose the correct COM port (Windows Device Manager) or device path on Linux/macOS. Press Refresh after plugging in USB. Use only one program on that port.
  4. Two-way CAT firmware is required (serial number 8G05xxxx and later per Yaesu). If the radio never answers a poll, check firmware and cabling before chasing Doppler.

The status bar should show the radio connected when Enable radio is on and the port is free. Use Test or start tracking on a pass to confirm frequencies move.

[Screenshot placeholder: rear panel CAT/LINEAR jack and CT-62 wiring.]

Satellite mode on the FT-847

Cross-band satellites need uplink and downlink on different bands. That is what the FT-847 SAT mode is for.

  1. Press [SAT] on the front panel. The satellite icon appears on the display. OscarWatch also sends satellite mode on over CAT when a cross-band pass starts.
  2. Press [HOME] (RX) so the main display and MAIN VFO tuning dial control the downlink. The Sub display holds the uplink; use the SUB-TUNE knob only if you need a manual uplink tweak (OscarWatch normally sets SAT TX over CAT).
  3. Do not use ordinary [SPLIT] for full-duplex satellite work. SPLIT is for a different operating style (transmit on one VFO, receive on another outside SAT). OscarWatch uses SAT RX and SAT TX opcodes, not SPLIT.
  4. [N/R] in satellite mode selects normal or reverse tracking when you turn the main dial (Sub moves with Main). OscarWatch sets receive and transmit frequencies independently for Doppler, so you do not have to match SatPC32 tracking habits. Leave tracking as you prefer for manual tests; during OscarWatch control, frequency updates come from the app.

For same-band modes (for example ISS packet on 145 MHz), the FT-847 cannot hold separate receive and transmit frequencies on one band in satellite mode. OscarWatch turns satellite mode off and moves the main VFO between downlink and uplink for each transmit. See ISS packet and Terminal below.

Uplink and downlink must stay on different bands for full-duplex satellite mode. If both SAT frequencies are on one band, the radio shows Error and will not transmit.

Hearing the downlink (AF and squelch)

Downlink audio comes from the main receiver path to the speaker or headphones.

  1. Confirm [HOME] (RX) is selected so you are listening to the downlink on the main display, not [VFO/M] (TX).
  2. Set the inner AF control to a comfortable level. The rear DATA and PKT jacks use fixed levels; they are not controlled by the front-panel AF knob.
  3. On FM satellites, set SQL just above the noise floor. If squelch is too tight, you will think the downlink is dead when the satellite is weak.
  4. On FM, avoid CTCSS decode on the downlink unless the satellite actually carries that tone. OscarWatch programs the uplink tone encoder only on SAT TX. Tone decode on receive can mute the audio when no tone is present.

During SSB satellite operation, the manual notes that SSB voice monitor is disabled in satellite mode so you can monitor your downlink return from the satellite without the monitor fighting it.

Before your first pass

  1. Close other CAT applications on the FT-847 port.
  2. Settings → Radio: rig FT-847, correct port, baud matching menu #37, radio enabled. Leave Dual radio off for this guide.
  3. In the frequency panel, pick the satellite and transponder mode. Use Full Doppler unless you know you need RX-only or TX-fixed.
  4. Confirm the radio is on the right bands (for example 2 m downlink and 70 cm uplink for a Mode V/U bird). OscarWatch sets modes from the catalogue (USB, LSB, CW, FM, DATA-USB, DATA-LSB, DATA-FM, and narrow variants where applicable).
  5. Press Resume tracking when the pass is in range (not Standby).
  6. Optional: untick Turn satellite mode off when OscarWatch closes in Settings → Radio if you want the FT-847 to stay in satellite mode after OscarWatch quits (when ticked, OscarWatch exits SAT on disconnect, as on other satellite rigs).

[Screenshot placeholder: FT-847 front panel with SAT active and HOME (RX) lit.]

What OscarWatch controls during tracking

For cross-band passes:

  • Satellite mode on or off to match the transponder (off for same-band ISS packet and beacon-only downlink).
  • SAT RX (Main) and SAT TX (Sub) frequencies for Doppler (10 Hz steps over CAT).
  • Modes on SAT RX and SAT TX from the frequency panel (for example USB downlink and LSB uplink on an inverting linear bird).
  • Uplink CTCSS when the database lists a tone (encoder on SAT TX only).
  • Passband trim on linear USB, LSB, and CW: spin the main dial to hunt, then pause so OscarWatch can resume Doppler — see spinning the dial.

OscarWatch cannot exchange Main and Sub over CAT. If bands are swapped on the front panel, fix roles with [HOME] (RX) and the band keys, then let pass setup run again.

When you disconnect, OscarWatch clears uplink tone and exits satellite mode if Turn satellite mode off when OscarWatch closes is ticked, then sends CAT off.

Doppler behaviour

OscarWatch uses the same Doppler policy as other satellite rigs:

  • FM downlink modes use Doppler threshold FM (default 350 Hz).
  • USB, LSB, and CW use Doppler threshold SSB/CW (default 50 Hz).
  • DATA-USB, DATA-LSB, and DATA-FM threshold at 0 Hz (continuous updates).

Optional Adaptive threshold near TCA and Lead Doppler for CAT latency behave as described in Doppler tuning. Increase CAT delay if commands are missed.

On FM, Yaesu rigs in OscarWatch may lock the dial while tracking; use Pause CAT if you need manual tuning.

For receive-only modes (uplink 0), OscarWatch leaves satellite mode off and tracks the downlink on the main VFO only — see receive-only overview.

Supported modes (OscarWatch CAT)

OscarWatch sets these mode names on SAT RX and SAT TX as appropriate:

Catalogue mode CAT mode
USB, DATA-USB USB
LSB, DATA-LSB LSB
CW CW (wide or narrow)
CWR CWR
AM AM
FM, DATA-FM, FM-DATA FM (wide or narrow FMN)

Mode commands are applied after SAT frequencies and uplink tone on the FT-847 so wide FM is not forced narrow by the programming order.

OscarWatch does not read RF power from the FT-847. Set power on the radio. The FT4 Lower RF power to 30 W checkbox only applies where the driver reads power (not on the FT-847).

FT4 and data modes (audio path)

Digital modes use audio through the rear panel, not the microphone jack.

Use Jack Notes
SSB data (FT4, RTTY, SSTV decode on SSB) DATA IN/OUT (3.5 mm) Fixed RX level on the ring; TX audio on the tip with PTT on the same jack for AFSK
FM packet (1200/9600 baud) PKT (6-pin mini-DIN) Menu #23 sets 1200 or 9600 baud packet rate on the radio

In OscarWatch FT4, choose your USB soundcard for input and output, and use PTT → CAT so OscarWatch keys over the same CAT lead. Wire radio DATA OUT (or suitable RX tap) to the soundcard input and soundcard output to DATA IN at the levels in the FT-847 operating manual (approximately 200 mV RX, 20 mV TX at the jack).

OscarWatch sets USB or LSB over CAT when the transponder mode is DATA-USB or DATA-LSB; it does not route audio. You still need a physical interface (DigiRig, RigBlaster, separate soundcard, or homebrew) on DATA IN/OUT.

For linear FT4, keep Doppler audio correction enabled in FT4 settings unless you are debugging.

[Screenshot placeholder: DATA IN/OUT cable to a USB soundcard interface.]

ISS packet and Terminal

On same-band satellites, OscarWatch turns satellite mode off and uses a transmit hold on the main VFO: before each packet it moves to the Doppler uplink, transmits, then returns to the downlink. Built-in Terminal and the built-in modem use TXDELAY and TXTAIL for that timing on the FT-847.

If the radio cannot move to the uplink in time, the frame is not sent and the status line says so. See Terminal → Yaesu FT-847 and Yaesu radios.

Troubleshooting

Symptom Things to check
No CAT / rig not found Menu #37 baud matches Settings; null-modem cable; CT-62; port not used by another app; radio powered on
Frequencies stuck Pause CAT off; not in Standby; pass has uplink and downlink; cross-band satellite selected
Error on transmit Uplink and downlink on the same band in SAT — expected for invalid SAT layout; for ISS, OscarWatch should leave SAT (if not, pick the correct mode)
Cannot hear downlink [HOME] (RX) selected; AF up; SQL not too tight on FM; downlink band and mode correct
Uplink tone but no access Tone not in the FT-847 table for that frequency; OscarWatch logs unsupported tones
FM sounds “thin” after CAT Known quirk: mode is programmed after tone; pass setup reasserts wide FM and encoder-only tone
Terminal frames not sent Same-band hold failed (still on downlink); check TXDELAY/TXTAIL; see Terminal status line

Increase CAT delay under Settings → Radio if updates are intermittent. Power-cycle the FT-847 after a heavy CAT session if the radio stops answering.

Related topics

OscarWatch
OscarWatch
Toggle sidebar