ICOM IC-910 / IC-910H with OscarWatch Tracker
The IC-910 family is a classic VHF/UHF satellite rig: one radio, two bands, and satellite mode so you can hear the downlink on MAIN while you transmit on SUB. OscarWatch drives frequency, mode, satellite layout, and (where the satellite needs it) uplink CTCSS over CI-V.
This page is for operators who may be new to the 910's satellite layout, or who are moving from another program or a hardware controller and want the radio itself right as well as OscarWatch. For other ICOM rigs, see ICOM radios. For wiring and pass behaviour in general, start at Radio and rotator.
On this page
- CI-V connection
- OscarWatch settings
- Satellite mode on the radio
- MAIN and SUB in a pass
- Audio and squelch
- What OscarWatch does on a pass
- Supported modes
- FT4 and other data modes
- Troubleshooting
CI-V connection
The IC-910H has no built-in USB port. Computer control uses the rear [REMOTE] jack and an Icom CT-17 CI-V level converter, or a third-party USB CI-V cable that presents a serial port to the PC.
- Connect REMOTE to the converter or adapter, then the adapter to the PC.
- Power the radio before opening the serial port in OscarWatch.
- Use a dedicated COM port (or Linux
by-idpath). Radio, rotator, and GPS each need their own port — see Linux serial ports. - Close other programs that might hold the same port.
On the radio, open the CI-V set mode (push [SET] until the CI-V items appear; the IC-910H manual describes this under set mode):
| Radio setting | What to use |
|---|---|
| CI-V address | Factory default 60H. OscarWatch's default when you pick ICOM IC-910 is 7C (hex); the address in Settings → Radio must match whatever you set here. If you left the radio on 60, enter 60 in OscarWatch. |
| CI-V baud rate | Choose a fixed rate and match it in OscarWatch. 19200 bps is the usual choice with OscarWatch; the radio also offers Auto, 300, 1200, 4800, 9600, and 19200. |
| CI-V transceive | On is recommended so the radio reports dial and mode changes back to the PC. |
The [REMOTE] indicator on the front panel lights when CI-V remote control is active.
Screenshot placeholder: rear panel with REMOTE jack labelled, and set-mode screen showing CI-V address, baud rate, and transceive.
OscarWatch settings
Open Settings → Radio (save when finished).
| Setting | IC-910 notes |
|---|---|
| Rig type | ICOM IC-910 (same driver for IC-910, IC-910D, and IC-910H). |
| IC-910 model | Shown when rig type is IC-910. CI-V cannot tell the 20 W, 50 W, and H sets apart — choose the 144 MHz power rating printed for your radio (H, D, or 20 W). A saved IC-910 stays on the H ratings unless you change this. Used for FT4 power checks. |
| COM port | The CI-V serial port (Device Manager on Windows; by-id on Linux). |
| Baud rate | Must match the radio CI-V menu (often 19200). |
| CI-V address (hex) | Must match the radio (factory 60; OscarWatch suggests 7C when you first select IC-910 — change to match your radio). |
| CAT delay (ms) | Spaces CI-V commands. Increase if commands are missed; default is usually fine. |
| Turn satellite mode off when OscarWatch closes | When ticked (default), OscarWatch turns satellite mode off on exit if it turned it on for the pass. Untick if you prefer the radio to stay in satellite mode. |
Press Save, then track a satellite and confirm the status bar shows the radio connected. If CI-V does not respond after using another rig on the same cable, quit OscarWatch, unplug and replug USB, and restart.
For Doppler thresholds, passband tuning, and uplink delay after you spin the dial, see Doppler tuning and ICOM radios (shared behaviour for Main/Sub rigs).
Satellite mode on the radio
Most OscarWatch passes are cross-band: downlink and uplink are on different bands (for example 70 cm down, 2 m up). The IC-910H is built for that in satellite mode — receive on MAIN, transmit on SUB, with normal or reverse tracking as required by the satellite.
You can enter satellite mode on the radio at any time:
- Push [SATELLITE] to toggle satellite mode (RX on MAIN, TX on SUB).
- Push [SATELLITE] for 1 sec. to copy the current MAIN (downlink) and SUB (uplink) frequencies into the satellite VFOs.
- Push [F-INP/ENT] for 1 sec. to switch normal and reverse tracking (
SATL NOR/SATL REVon the display). OscarWatch sets frequencies and modes for each pass; reverse satellites in the database still need the correct tracking sense on the radio when you work manually.
OscarWatch turns satellite mode on with CI-V command 1A 07 01 when you start tracking a normal cross-band satellite (and off with 1A 07 00 when appropriate). You do not need to press [SATELLITE] first, though many operators still set bands and audio on the front panel before the pass.
Receive-only satellites (uplink 0 in the database, such as ISS SSTV) are different: OscarWatch turns satellite mode off, puts the downlink on MAIN only, and does not configure uplink. See receive-only overview.
Dual radio: the IC-910 can be one leg of a two-radio station with satellite mode off on that leg; see ICOM dual radio. This page focuses on single-radio satellite mode, which is the normal IC-910 setup.
Screenshot placeholder: front panel in satellite mode with MAIN downlink and SUB uplink frequencies visible, and
SATL NORorSATL REVindication.
MAIN and SUB in a pass
In satellite mode the roles are fixed on the IC-910H:
| VFO | Role in satellite mode | What you use it for |
|---|---|---|
| MAIN | Receive (downlink) | Passband audio, S-meter for the transponder, tuning the downlink when you hunt SSB |
| SUB | Transmit (uplink) | Your transmit frequency and mode; OscarWatch applies Doppler on Sub as well |
OscarWatch selects VFOs over CI-V with Main = 07 D0 and Sub = 07 D1. If the satellite's bands are swapped relative to the radio front panel, OscarWatch can send 07 B0 to exchange MAIN and SUB so the target downlink band sits on MAIN.
While you spin the receive dial on a linear pass, OscarWatch keeps you on MAIN and delays uplink (Sub) CAT briefly so scanning the passband does not select Sub by accident. Defaults: Resume CAT after dial 800 ms, Uplink CAT wait after dial 2500 ms (Settings → Radio). See spinning the dial.
Audio and squelch
The IC-910H has separate [AF] (inner) and [RF/SQL] (outer) controls for MAIN and SUB.
Downlink audio is on MAIN. For satellite listening, set MAIN [AF] to a comfortable level and adjust MAIN [RF/SQL] for your mode:
- FM: rotate [RF/SQL] fully counterclockwise to open the squelch, then clockwise until the noise just disappears (manual p. 38).
- SSB/CW: with default assignments, squelch typically opens around the 12 o'clock [RF/SQL] position; rotate for maximum RF gain without excess floor noise.
SUB is your uplink, not the passband you copy. In satellite mode, SUB [AF] does not replace MAIN audio for the downlink. Operators who turn SUB audio down or leave SUB squelch tight after using dual-band receive can still miss traffic if they are also not checking MAIN [AF] and MAIN [RF/SQL]. For a loop test (whistle on uplink, hear yourself on the downlink), follow the manual: downlink on MAIN, uplink on SUB, and listen on MAIN.
SUB [RF/SQL] still matters on FM passes if you use the SUB band indicator or monitor paths; when in doubt, open MAIN squelch as above before chasing CAT or OscarWatch settings.
Screenshot placeholder: front panel close-up of MAIN and SUB AF/SQL knobs with labels.
What OscarWatch does on a pass
When you track a satellite with CAT enabled, OscarWatch typically:
- Turns satellite mode on (
1A 07 01) for cross-band satellites. - Puts downlink on MAIN and uplink on SUB, exchanging bands with
07 B0when needed. - Sets mode on each VFO (USB, LSB, FM, FM narrow, CW, and catalogue data modes — see Supported modes).
- Writes frequencies on Main and Sub for Doppler and applies your RX and TX offsets.
- Sends uplink CTCSS when the satellite database specifies a tone and the radio supports it over CI-V.
- Keeps MAIN selected for receive while you hunt SSB on the dial (uplink CAT follows after the dial timers above).
Doppler behaviour (thresholds, adaptive TCA, lead for CAT latency, and when DATA-* modes update every step) is the same as for other ICOM Main/Sub rigs — see Doppler tuning.
When you quit or disconnect, OscarWatch can clear uplink tone, turn satellite mode off, and leave the radio on MAIN (unless you disabled Turn satellite mode off when OscarWatch closes).
Supported modes
OscarWatch sets modes with CI-V 0x06 on the IC-910. Catalogue strings map as follows (from the IC-910 driver and shared ICOM codec):
| Database mode | CI-V behaviour on IC-910 |
|---|---|
| USB, LSB, CW | Standard 06 mode bytes |
| FM | 06 05 01 (wide FM) |
| FMN | 06 05 02 (narrow FM filter) |
| DATA-USB, DATA-LSB, DATA-FM | Same as USB, LSB, or FM — the IC-910 has no USB-D / FM-D data sideband over CI-V |
The IC-910 does not expose separate data-sideband modes like the IC-9700. Voice and data catalogue entries use the ordinary mode on the radio; data audio is wired separately (below).
For linear SSB, Voice / CW in the frequency panel and Linear CW: keep receive in USB/LSB in Settings follow the same rules as other ICOM rigs — see Frequencies.
FT4 and other data modes
The IC-910 has no USB soundcard. Receive and transmit audio for FT4, packet, or AFSK must go through an external interface on the rear DATA (MAIN) or DATA (SUB) socket, or the ACC(1) socket, as described in the IC-910H manual (chapter 9, Data communication). The manual covers AFSK levels (for example 0.4 V p-p recommended into DATA IN), PTT lines, and AF OUT for receive.
Practical notes for OscarWatch:
- Pick USB or LSB (or FM for some packet setups) in the frequency panel; OscarWatch sets the radio mode accordingly. It does not route audio — you choose the interface and soundcard in OscarWatch FT4 → Settings → Soundcards or in Recording / other tools.
- Use DATA (MAIN) for downlink audio from the passband you hear on MAIN in satellite mode. Match your interface to the manual pinout for DATA IN, DATA OUT, PTT, and AF OUT.
- PTT in FT4 can use CAT on the same CI-V port OscarWatch already uses for Doppler.
- Set IC-910 model under Settings → Radio so FT4 power checks map CI-V power levels correctly (H / D / 20 W).
Screenshot placeholder: DATA (MAIN) socket wiring diagram from the manual, annotated for a typical soundcard interface.
Troubleshooting
| Symptom | Things to check |
|---|---|
| No CAT / wrong COM port | CI-V address and baud match; transceive On; only one app on the port; try replug USB after switching from another rig (troubleshooting). |
| Frequencies do not move | Satellite tracking started? Pause CAT off? Radio in satellite mode for cross-band (OscarWatch usually sets this). |
| No downlink audio | MAIN [AF] and MAIN [RF/SQL] for your mode; correct MAIN band and mode; antenna and preamp as needed. SUB controls do not substitute for MAIN listen audio in satellite mode. |
| Uplink late after tuning MAIN | Normal until Uplink CAT wait after dial (default 2500 ms) elapses (Doppler tuning). |
| Radio stuck on SUB / odd VFO | Press Resume tracking if Standby is on, or toggle [SATELLITE] on the radio; see troubleshooting. |
| FT4 blocked for power | Choose the correct IC-910 model; power is read over CI-V 14 0A when you press Enable Tx or Tune (FT4 power). |
| Split on, satellite mode will not set | OscarWatch refuses satellite mode while split is on; turn split off on the radio. |
If problems persist, note whether the issue appears with OscarWatch closed (radio-only) or only when tracking. That narrows squelch and band layout versus CI-V settings.
Tip: After maintenance or a factory reset on the radio, confirm CI-V address 60H, baud rate, and transceive again before the next pass.